Products

Bang Wei Dun KN95 PM2.5 Respirator Face Masks x10 from NSE Imports #1.

Bang Wei Dun KN95 PM2.5 Respirator Face Masks x10 from NSE Imports #2.

Ships from: The UK Bang Wei Dun KN95 PM2.5 Respirator Face Masks x10 £19.99

Protect yourself with these excellent Bang Wei Dun KN95 rated masks (equivalent to N95/FFP2, see images for details). Hygienically sealed packs of 10 masks ensure they arrive safely and free of contaminants. Most commonly used for Flu, Influenza, Swine Flu and Avian Flu prevention, the CDC consider N95 masks help to prevent the spreading and transmission of viruses from person to person. N95 masks are designed to fit over the nose and mouth of the wearer, and properly fitted can provide excellent protection. Ideal for use in conditions where Social Distancing may not be possible, these include shops, transport and healthcare situations.Read more on our Respirator Advice and Information Page.Please be aware: For hygiene reasons once the packet has been opened we cannot accept returns on this item. Features: N95/KN95 Rated Respirator facemask, equivalent to FFP2 rating. Wrapped in pairs of masks, keep a spare pair handy. Adjustable nose bridge for a secure fit. Can help you prevent spreading any germs you may have. Removes 95% of all dust or particles that are at least 0.3 microns in diameter. High quality 4 layer design, easy to breath through while offering protection. No staples or exposed metal parts. Bonded straps ensure the mask will stay secure. Manufactured February 2020 (See images for test reports). Supplied in packs of 10. Usage Advice: For male wearers, please ensure your are clean shaven. Beards or long stubble can prevent the mask sealing to your face. Ensure Nose Bridge is adjusted to seal against your face. Avoid touching the mask once it’s secured on your face, as it might have germs on it Avoid dangling the mask from one ear or hanging the mask around your neck as a chin warmer. Ensure both mouth and nose are covered, an exposed nose defeats the protection benefits of a mask. Removal Advice: Before you take off the mask, wash your hands. Avoid touching the mask itself, as it could be contaminated. Hold it by the loops only. Carefully remove the mask from your face once you unhook both ear loops. Holding the mask loops, discard the mask in a covered rubbish bin. If you are not near a bin, place inside a bag you can seal or tie shut. After removing the mask, wash your hands thoroughly once more.

Sold out

BL-Touch Auto Bed Levelling Sensor: Improve your 3D prints with automatic bed levelling from NSE Imports #1.

BL-Touch Auto Bed Levelling Sensor: Improve your 3D prints with automatic bed levelling from NSE Imports #2.

Ships from: The UK BL-Touch Auto Bed Leveling Sensor: Improve your 3D prints with automatic bed leveling £19.95

The BL-Touch Auto Bed Leveling Sensor is a popular upgrade for 3D printers. It uses a sensor to measure the distance between the print head and the heated bed, and then automatically adjusts the Z-axis height during printing. This ensures that the first layer is always laid down correctly, even if the bed is not perfectly level. The BL-Touch is easy to install and use. Simply mount the sensor to your printer, connect the wires, and enable the auto leveling feature in your printer's firmware. Features: Automatic bed leveling High precision Easy to install and use Improves print quality Reduces failure rates Specifications: Voltage: 5V Current: 15mA Maximum(Peak) Current: 300mA Case Material: Polycarbonate(PC) Case Colour: Semitransparent White Cable Length: 150mm PCB & Soldering: RoHS, Lead Free (Pb Free) Package Included: 1 x ANTCLABS BLTouch Auto Bed Levelling Sensor 2 X Dupont Housing Shell 3Pin 2 X Dupont Housing Shell 2Pin 2 X Dupont Housing Shell 1Pin 10 X Dupont Terminal 1 X Jumper Cap With Screw & Nut & Washer Manual and More Info RAMPS1.3/1.4, MKS-Gen V1.3, MKS-Base V1.4, etc. installation: Click Here MKS-Base V1.2, mini-Rambo, etc. installation: Click Here 32bit board installation: Click Here Setup Manual: Click Here Marlin Manual Click Here

Bweitai KN95 (equivalent to FFP2) PM2.5 Respirator Masks (10 Pack) from NSE Imports #1.

Bweitai KN95 (equivalent to FFP2) PM2.5 Respirator Masks (10 Pack) from NSE Imports #2.

Ships from: The UK Bweitai KN95 (equivalent to FFP2) PM2.5 Respirator Masks (10 Pack) £19.99

Protect yourself with these excellent Bweitai KN95 rated masks (equivalent to N95/FFP2, see images for details). Hygienically sealed packs of 10 masks ensure they arrive safely and free of contaminants. Most commonly used for Flu, Influenza, Swine Flu and Avian Flu prevention, the CDC consider N95 masks help to prevent the spreading and transmission of viruses from person to person. N95 masks are designed to fit over the nose and mouth of the wearer, and properly fitted can provide excellent protection. Ideal for use in conditions where Social Distancing may not be possible, these include shops, transport and healthcare situations.Read more on our Respirator Advice and Information Page.Please be aware: For hygiene reasons once the packet has been opened we cannot accept returns on this item. Features: N95/KN95 Rated Respirator facemask, equivalent to FFP2 rating. Wrapped in pairs of masks, keep a spare pair handy. Adjustable nose bridge for a secure fit. Can help you prevent spreading any germs you may have. Removes 95% of all dust or particles that are at least 0.3 microns in diameter. High quality 4 layer design, easy to breath through while offering protection. No staples or exposed metal parts. Bonded straps ensure the mask will stay secure. Manufactured February 2020 (See images for test reports). Supplied in packs of 10. Usage Advice: For male wearers, please ensure your are clean shaven. Beards or long stubble can prevent the mask sealing to your face. Ensure Nose Bridge is adjusted to seal against your face. Avoid touching the mask once it’s secured on your face, as it might have germs on it Avoid dangling the mask from one ear or hanging the mask around your neck as a chin warmer. Ensure both mouth and nose are covered, an exposed nose defeats the protection benefits of a mask. Removal Advice: Before you take off the mask, wash your hands. Avoid touching the mask itself, as it could be contaminated. Hold it by the loops only. Carefully remove the mask from your face once you unhook both ear loops. Holding the mask loops, discard the mask in a covered rubbish bin. If you are not near a bin, place inside a bag you can seal or tie shut. After removing the mask, wash your hands thoroughly once more.

Comgrow T300 3D Printer: Wi-Fi capable Klipper powered 3D Printer from NSE Imports #1.

Comgrow T300 3D Printer: Wi-Fi capable Klipper powered 3D Printer from NSE Imports #2.

Ships from: The UK Comgrow T300 3D Printer: Wi-Fi capable Klipper powered 3D Printer £379.95

The Comgrow T300 offers a sturdy platform for your 3D printing. With a large 300 x 300 x 350mm build size, linear rails, and 81 point auto levelling, you can quickly and easily make your designs come to life. Comgrow are part of the Sovol group, while the T500 retains the Comgrow brand they are the same company. The T300 also features Wi-Fi connectivity, you no longer need to hover over your printer, able to be monitored and controlled from your PC or Phone you can leave it to get on with printing while you are elsewhere. Save 5% on Your First Filament Order!* Features: Large Build Volume: Print larger objects in one go, reducing the need for segmentation and assembly. Industrial-Grade Precision: Experience exceptional print quality with smooth movements thanks to robust linear rails on all axes. These rails ensure minimal friction and vibration, leading to highly accurate prints. High-Temperature Printing: The all-metal hot-end allows printing with a wider range of filaments at temperatures up to 300°C. Precision Extrusion: The innovative planetary dual-gear direct drive extruder ensures smooth and reliable filament feeding for accurate prints. Easy Levelling: The 81-point auto levelling with an inductive sensor simplifies setup and guarantees a perfect first layer. Intuitive Interface: The large 4.3-inch touchscreen offers a user-friendly experience for navigating settings and monitoring prints. UPC: 500101008525 See our images for more specifications and features. Warranty and Support: This 3D Printer ships directly from SOVOL ensuring the latest stock is supplied. All SOVOL/COMGROW 3D Printers have a 12 month guarantee. We provide support in the first instance, if required we will refer it to SOVOL for technical advice or spares to be sent. Please see the 'Info' link at the top of the description for more information. We will send details of this after purchase, or contact us for more information. *When you purchase a SOVOL printer, we'll email a voucher code to use on your filament order.

Add to cart

Comgrow T500 3D Printer: Extra large format Klipper powered 3D Printer from NSE Imports #1.

Comgrow T500 3D Printer: Extra large format Klipper powered 3D Printer from NSE Imports #2.

Ships from: The UK Comgrow T500 3D Printer: Extra large format Klipper powered 3D Printer £799.95

The Comgrow T500 is a big-time 3D printing powerhouse, perfect for conquering colossal creations. With a whopping 500 x 500 x 500mm build size, you can unleash your imagination without any limits. Comgrow are part of the Sovol group, while the T500 retains the Comgrow brand they are the same company. The T500 is ideal for makers, businesses, and professionals who require a 3D printer capable of handling ambitious projects with industrial-grade precision. Save 5% on Your First Filament Order!* Features: Monumental Build Volume: Print large objects in one go, eliminating the need for segmentation and assembly. Industrial-Grade Precision: Experience exceptional print quality with smooth movements thanks to robust linear rails on all axes. These rails ensure minimal friction and vibration, leading to highly accurate prints. High-Temperature Printing: The all-metal hot-end allows printing with a wider range of filaments at temperatures up to 300°C. Precision Extrusion: The innovative planetary dual-gear direct drive extruder ensures smooth and reliable filament feeding for accurate prints. Triple cooling fan system: Rapidly cool your printed material with Sovol's innovative triple cooling fan setup. LED Lights: Clearly see how material is being deposited with the on head LED lighting. Easy Levelling: The 49-point auto levelling with an inductive sensor simplifies setup and guarantees a perfect first layer. Intuitive Interface: The large 7-inch touchscreen offers a user-friendly experience for navigating settings and monitoring prints. UPC: 500105007107 See our images for more specifications and features. Warranty and Support: This 3D Printer ships directly from SOVOL ensuring the latest stock is supplied. All SOVOL/COMGROW 3D Printers have a 12 month guarantee. We provide support in the first instance, if required we will refer it to SOVOL for technical advice or spares to be sent. Please see the 'Info' link at the top of the description for more information. We will send details of this after purchase, or contact us for more information. *When you purchase a SOVOL printer, we'll email a voucher code to use on your filament order.

Add to cart

sale

ERYONE 1kg 1.75mm Galaxy Glitter PLA Filament 3D Printer Filament Perfect Spooled Sparkle Shining Material Glittering Props from NSE Imports #1.

Ships from: The UK ERYONE 1kg 1.75mm Galaxy Glitter PLA Filament 3D Printer Filament Perfect Spooled Sparkle Shining Material Glittering Props from £19.95 £22.95

ERYONE Galaxy Glittering PLA Filament brings a little bling to your prints, made from high quality virgin plastic and with strong colours and a dazzling sparkling finish, supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. This is a great filament for making props and cosplay items. No need to try and coat an item with glitter after printing, the glitter finish runs through your print as well, meaning the odd scuff won't leave bald patches. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as: Prusa,Makerbot,etc. ERYONE filament had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 210-220°C Peak Melting Temp: 155±5°C> Heated Bed Temp: 55-70°C Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Specific Gravity [g/cm3]: 1.24 MFR [g/10min]: 6 Tensile Strength [MPa]: 61 Elongation at Yield [%]: 3.2 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

-34% sale

ERYONE ABS 1.75mm 3D Printing Filament 1kg Ideal for Hard Wearing Prints from NSE Imports #1.

ERYONE ABS 1.75mm 3D Printing Filament 1kg Ideal for Hard Wearing Prints from NSE Imports #2.

Ships from: The UK ERYONE ABS 1.75mm 3D Printing Filament 1kg Ideal for Hard Wearing Prints £17.95 £26.95

ERYONE ABS filament is a new material designed to durable and heat resistant prints. It's great for mechanical parts and parts needing a high heat resistance. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with most 3D Printers that support 1.75mm ABS filament. NOTE: Requires good ventilation during printing due to stronger fumes that are typical with ABS. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 230-260°C Heated Bed Temp: 90-110°C Fan Speed: None to Minimal Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

-33% sale

ERYONE ASA 1.75mm 3D Printing Filament 1kg UV Resistant Superior to ABS Ideal For Hard Wearing Prints And Outdoor Prints from NSE Imports #1.

ERYONE ASA 1.75mm 3D Printing Filament 1kg UV Resistant Superior to ABS Ideal For Hard Wearing Prints And Outdoor Prints from NSE Imports #2.

Ships from: The UK ERYONE ASA 1.75mm 1kg 3D Printing Filament: UV Resistant Superior to ABS Ideal For Hard Wearing Prints And Outdoor Prints £18.95 £27.95

ERYONE ASA (Acrylonitrile styrene acrylate) filament is a new material designed to give UV Resistant prints with similar strengths and quality to ABS. Providing superior heat and chemical resistance to ABS it's great for parts for used in outdoor, automotive and hostile environments. While easy to print and less prone to warping than ABS, care should be taken not to overcool the print for best results. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with most 3D Printers that support 1.75mm ABS filament. NOTE: Requires good ventilation during printing due to the presence of styrene. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 230-260°C Heated Bed Temp: 90-110°C Fan Speed: None to Minimal Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg FAQ: Clogging: Clogging can occur due to an uneven wire diameter or a temperature that is too low. To reduce the likelihood of clogging, clean the nozzle before use and increase the temperature. Stringing: Stringing can occur if the temperature is excessively high, the filament flow is too rapid, or the feed parameters are incorrectly set. Adjusting the temperature and speed settings appropriately can resolve these issues. Over Extrusion: Excessive temperature, slow extrusion speed, or a mismatched nozzle diameter can lead to over-extrusion at the nozzle outlet, resulting in residual material.

Add to cart

sale

ERYONE Dual Colour 1kg 1.75mm PLA 3D Printer Filament Regular, Matte and Silk Colours Create Great Two Tone Prints from NSE Imports #1.

ERYONE Dual Colour 1kg 1.75mm PLA 3D Printer Filament Regular, Matte and Silk Colours Create Great Two Tone Prints from NSE Imports #2.

Ships from: The UK ERYONE Dual Colour 1kg 1.75mm PLA 3D Printer Filament Regular, Matte and Silk Colours Create Great Two Tone Prints from £19.95 £30.95

ERYONE Dual Colour PLA Filament is ideal for creating eye catching prints. With a range of colour choices, these print similar to Rainbow filaments but with just two mixed colours. Available in Regular, Matte and Silk options. The 4x mixed spool options contain the following: 4x 250g Matte Dual: Yellow/Purple, Blue/Purple, Green/Purple, Blue/Yellow 4x 250g Silk Dual (A): Blue/Green, Red/Green, Red/Blue, Purple/Gold 4x 250g Silk Dual (B): Gold/Bronze, Gold/Silver, Red/Gold, Yellow/Green Made from high quality virgin plastic, with strong colours and supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. This is a great filament for making props and cosplay items. No need to try and coat an item with glitter after printing, the glitter finish runs through your print as well, meaning the odd scuff won't leave bald patches. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as: Prusa,Makerbot,etc. ERYONE filament had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 210-220°C Peak Melting Temp: 155±5°C> Heated Bed Temp: 55-70°C Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Specific Gravity [g/cm3]: 1.24 MFR [g/10min]: 6 Tensile Strength [MPa]: 61 Elongation at Yield [%]: 3.2 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

sale

ERYONE Luminous PLA Filament 1.75mm 1kg Glow in the Dark Green 3D Printer Filament Ideal for Halloween from NSE Imports #1.

ERYONE Luminous PLA Filament 1.75mm 1kg Glow in the Dark Green 3D Printer Filament Ideal for Halloween from NSE Imports #2.

Ships from: The UK ERYONE Luminous PLA Filament 1.75mm 1kg Glow in the Dark Green 3D Printer Filament Ideal for Halloween from £15.95 £27.95

ERYONE Luminous PLA Filament is a high quality Glow in the dark PLA Filament that's great for creating Halloween model and props, prints and parts. Great for sculptures, cosplay and model making. Suits most 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Easythreed and more. Features: Contains noctilucent power, Charge from Sunlight, Incandescent lamp, Ultraviolet light. Make awesome Glow in the dark prints. High Dimensional Accuracy: 1.75mm, tolerance +/-0.03mm. No Tangling: Perfect winded filament PLA, 100% tangle-free before unopened, neatly rolled, no curling or warping. High Compatibility: Universal compatibility with diverse 99% common-used FDM 3D printers in market. Vacuumed Sealed Packaging: The filament comes in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust. Eco-friendly: Made from Corn Starch and PLA, fully recyclable. Specifications: Filament Diameter: 1.75mm Finish: Glow in the Dark Green Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 200-220°C Heated Bed Temp: 55-70°C Recommended Print Speed 30-60mm/s In order to avoid corrosion, higher hardness steel nozzles are recommended. Gross weight: 1.35kg (approx) Net weight: 1kg (approx) FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

Sold out -18% sale

ERYONE Marble PLA 3D Printer Filament 1kg/2.2lbs 1.75mm for FDM 3D Printer and Pens Great for sculptures and models from NSE Imports #1.

ERYONE Marble PLA 3D Printer Filament 1kg/2.2lbs 1.75mm for FDM 3D Printer and Pens Great for sculptures and models from NSE Imports #2.

Ships from: The UK ERYONE Marble PLA 3D Printer Filament 1kg/2.2lbs 1.75mm for FDM 3D Printer and Pens Great for sculptures and models £18.95 £22.95

ERYONE Marble PLA Filament is a high-quality Marble PLA Filament that's great for creating realistic stone/marble prints and parts. Great for sculptures, cosplay and model making. Suits most 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Easythreed and more. Features: Marble Effect: Marble PLA is a mixture of pure PLA and marble elements, which produces natural marble effect. Precise Dimension: 1.75mm in diameter with tolerance ±0.03mm. Easy to Print: Ultrafine particles, easy to melt and print, and will not cause blockage. Excellent print quality. Vacuum Packaging: Every spool of filament is vacuum sealed to be kept away from moisture and will not be oxidized. Compatibility: 1.75mm diameter which is compatible with almost all kinds FDM 3D printer and pens. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.02mm Print Temperature: 190-220°C Recommended Print Temperature: 200-220°C Recommended Print Speed 30-60mm/s Heated Bed Temp: 55-70°C Gross wt: 1.35kg (approx) Net Weight: 1kg (approx) FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

sale

ERYONE Matte PLA Filament: 1kg 1.75mm 3D Printer Filament from NSE Imports #1.

ERYONE Matte PLA Filament: 1kg 1.75mm 3D Printer Filament from NSE Imports #2.

Ships from: The UK ERYONE Matte PLA Filament: 1kg 1.75mm 3D Printer Filament from £16.95 £19.95

ERYONE Matte PLA Filament brings a high quality finish without the shine of regular PLA, Made from high quality virgin plastic and with strong colours, supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints every time. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as:Prusa,Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 200-215°C Heated Bed Temp: 60-70°C Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Tensile Strength [MPa]: 82-85 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

Sold out

ERYONE Metallic PLA 3D Printer Filament: Magnetic filament for creative printers from NSE Imports #1.

ERYONE Metallic PLA 3D Printer Filament: Magnetic filament for creative printers from NSE Imports #2.

Ships from: The UK ERYONE Metallic PLA 3D Printer Filament: Magnetic filament for creative printers £20.95

ERYONE Metallic PLA Filament is infused with metal particles, not only does this provide a satin metal sheen to your prints, but also allows you prints to be attracted by magnets. Available in a range of bold colors, made from high quality virgin plastic and supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as:Prusa,Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 200-215°C Heated Bed Temp: 60-70°C Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Tensile Strength [MPa]: 82-85 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

-45% sale

ERYONE Mini Rainbow PLA 3D Printer Filament: More Frequent Changes Than Regular Rainbow Filaments from NSE Imports #1.

ERYONE Mini Rainbow PLA 3D Printer Filament: More Frequent Changes Than Regular Rainbow Filaments from NSE Imports #2.

Ships from: The UK ERYONE Mini Rainbow PLA 3D Printer Filament: More Frequent Changes Than Regular Rainbow Filaments £18.95 £33.95

ERYONE Mini Rainbow PLA Filament brings some multicolour action to your prints, with color changes every 9-11m of filament, you get more frequent changes of colour, each print will be unique, it produces models with a very high quality, colour packed finishes. Suits most 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Degradable and environmentally friendly, ERYONE filament is made from eco-friendly corn starch and the PLA itself can be recycled. Features: Color circulation: Red-Orange-Yellow-Green-Teal-Blue-Purple-Red Most rolls should start with Red but some may not due to spooling variances Shorter colour transactions, about 9-11m best seen on larger prints Stable Printing: Neatly rolled, high quality. Little Clogging: The diameter is strictly controlled at 1.75±0.03mm. Professional Packaging, Vacuumed Sealed: ERYONE filament is supplied in a sealed vacuum bag with a desiccant bag, keeping it dry and free from dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as: Prusa, Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Finish: Awesome Rainbows Tolerance: ± 0.05mm Print Temperature: 190-215°C Recommended Print Speed: 30-60mm/s Heated Bed Temp: 55-70°C Gross weight: 1.35kg (approx) Net Weight: 1kg (approx) FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

ERYONE PETG Filament 1kg 1.75mm: Various Colours For FDM 3D Printers from NSE Imports #1.

ERYONE PETG Filament 1kg 1.75mm: Various Colours For FDM 3D Printers from NSE Imports #2.

Ships from: The UK ERYONE PETG Filament 1kg 1.75mm: Various Colours For FDM 3D Printers from £13.95

ERYONE PETG Filament is a high quality PETG Filament, made from high quality virgin plastic and with strong colours, supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. PETG is an excellent choice for printing mechanically stressed parts. Compared to PLA, it is more heat resistant, more flexible and less brittle. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Higher strength and toughness than PLA The adhesion between layers is stronger than that of PLA Uniform wire diameter, smooth discharge and smooth surface Very good winding: Make the model looks shiny, no risk that the filament is entangled Very widely using: Acid and alkali resistance, can used in many applications Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as:Prusa,Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 230-250°C Heated Bed Temp: 55-70°C Recommended Print Speed 30-60mm/s Specific Gravity [g/cm3]: 1.27 Elongation at Yield [%]: 3.2 Tensile Strength [MPa]: 61 Moisture absorption – 1 day [%]: 0.13 Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

Sold out

ERYONE PETG Galaxy Glitter Filament: Add some sparkle to your prints from NSE Imports #1.

ERYONE PETG Galaxy Glitter Filament: Add some sparkle to your prints from NSE Imports #2.

Ships from: The UK ERYONE PETG Galaxy Glitter Filament: Add some sparkle to your prints £20.95

ERYONE Galaxy Glittering PETG Filament brings a little bling to your prints, made from high quality virgin plastic and with strong colours and a dazzling sparkling finish, supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. This is a great filament for making props and cosplay items. No need to try and coat an item with glitter after printing, the glitter finish runs through your print as well, meaning the odd scuff won't leave bald patches. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as: Prusa,Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 215-235°C Recommended Print Temperature: 210-220°C Peak Melting Temp: 155±5°C> Heated Bed Temp: 55-70°C Recommended Print Speed 20-80mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Specific Gravity [g/cm3]: 1.24 MFR [g/10min]: 6 Tensile Strength [MPa]: 61 Elongation at Yield [%]: 3.2 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

-34% sale

ERYONE PETG or PLA Carbon Fiber Filament: Ideal for Strong Lightweight Prints from NSE Imports #1.

ERYONE PETG or PLA Carbon Fiber Filament: Ideal for Strong Lightweight Prints from NSE Imports #2.

Ships from: The UK ERYONE PETG or PLA Carbon Fiber Filament: Ideal for Strong Lightweight Prints £19.95 £29.95

ERYONE Carbon Fiber filament is provide strong yet lightweight prints. Thanks to the infusion of Carbon Fiber into the filament you can create prints with thinner side walls without sacrificing rigidity. Available in both PLA and PETG you can choose the most suitable base material for your required design. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with most 3D Printers that support 1.75mm PLA or PETG filament. NOTE: Requires good ventilation during printing due to the presence of styrene. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature PLA Carbon Fiber: 190-220°C Print Temperature PETG Carbon Fiber: 220-240°C Heated Bed Temp: 55-70°C Fan Speed: None to Minimal Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

ERYONE PLA Filament: Various Colors For FDM 3D Printers from NSE Imports #1.

ERYONE PLA Filament: Various Colors For FDM 3D Printers from NSE Imports #2.

Ships from: The UK ERYONE PLA Filament: Various Colors For FDM 3D Printers from £17.95

ERYONE PLA Filament is a premium 3D printing material, made from high-quality virgin plastic and available in a vibrant range of colours. Their vacuum-sealed packaging keeps the filament fresh, while our tangle-free winding and precise tolerances ensure smooth, reliable prints every time. And now, their filament comes on eco-friendly, fully recyclable cardboard rolls. Compatible with popular 3D printers like: Creality 3D Artillery SUNLU Geeetech XVICO Eaythreed Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 210-220°C Peak Melting Temp: 155±5°C> Heated Bed Temp: 55-70°C Recommended Print Speed 30-100mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Specific Gravity [g/cm3]: 1.24 MFR [g/10min]: 6 Tensile Strength [MPa]: 61 Elongation at Yield [%]: 3.2 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

ERYONE PLA Plus Filament: Stronger than regular PLA with brighter colours from NSE Imports #1.

ERYONE PLA Plus Filament: Stronger than regular PLA with brighter colours from NSE Imports #2.

Ships from: The UK ERYONE PLA Plus Filament: Stronger than regular PLA with brighter colours £16.95

ERYONE PLA PLUs (PLA+) Filament is a high quality PLA Filament, based on their already outstanding PLA filament, ERYONE PLA PLUS improves the strength of the print over regular PLA to similar levels as PETG, but keeps the ease of printing that regular PLA brings. Made from high quality virgin plastic and with strong colours, supplied in vacuum packaging for freshness. Wound to prevent tangles, tight tolerance control and quality material ensures great prints everytime. Suits most FDM 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA | Non Toxic and Limited SmellERYONE filaments are 100% Made in the USA with virgin materials, Biodegradable and Eco-friendly, NO harm to user and environment. Ideal for indoor printing. Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High CompatibilityCompatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as:Prusa,Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 210-220°C Peak Melting Temp: 155±5°C> Heated Bed Temp: 55-70°C Recommended Print Speed 30-100mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg Specific Gravity [g/cm3]: 1.24 MFR [g/10min]: 6 Tensile Strength [MPa]: 61 Elongation at Yield [%]: 3.2 FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

-14% sale

ERYONE Rainbow PLA Filament Multicolor Perfect Spooled 1.75mm 1Kg Classic Rainbow Steampunk Rainbow Metal Silk from NSE Imports #1.

ERYONE Rainbow PLA Filament Multicolor Perfect Spooled 1.75mm 1Kg Classic Rainbow Steampunk Rainbow Metal Silk from NSE Imports #2.

Ships from: The UK ERYONE Rainbow PLA Filament Multicolor Perfect Spooled 1.75mm 1Kg Classic Rainbow Steampunk Rainbow Metal Silk £19.95 £22.95

ERYONE Rainbow PLA Filament brings some multicolour action to your prints, with color changes every 15m of filament, each print will be unique. With 4 colour choices, ranging from the very bold Metal Silk, to the the more subtle tones of the Steampunk Rainbow, it produces models with a very high quality, colour packed finish. Suits most 3D Printers from Creality 3D, Artillery, SUNLU, Geeetech, XVICO, Eaythreed and more. Degradable and environmentally friendly, ERYONE filament is made from eco-friendly corn starch and the PLA itself can be recycled. Features: Make some bold prints with Classic Rainbow and Metal Silk Make subtle colour changes with Rainbow Lagoon and Steampunk Rainbow Stable Printing: Neatly rolled, high quality. Little Clogging: The diameter is strictly controlled at 1.75±0.03mm. Professional Packaging, Vacuumed Sealed: ERYONE filament is supplied in a sealed vacuum bag with a desiccant bag, keeping it dry and free from dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with 3D Printers and 3D Pens that use 1.75MM filament, Such as: Prusa, Makerbot,etc. Our filaments had been tested on various brands of 3D printer in the market and with positive customers' feedback. Specifications: Filament Diameter: 1.75mm Finish: Awesome Rainbows Tolerance: ± 0.03mm Print Temperature: 190-220°C Recommended Print Temperature: 210-220°C Recommended Print Speed: 30-60mm/s Heated Bed Temp: 55-70°C Gross weight: 1.35kg (approx) Net Weight: 1kg (approx) FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.

Add to cart

Find anything you need

Friendly Service

Free Tracked Delivery to most destinations

Low Prices

Latest and Greatest Tech