3D Printer Auto Levelling Kits (5)

Building on their previous model Geeetech have gone back to the drawing board and released this new and updated auto bed level sensor for 3D Printers. The 3D touch v3.2 Pro is a new generation of FDM 3D printer hot bed automatic leveling accessory. It is compatible with glass, wood, metal and other materials of hot bed, bringing you a simpler and faster hot bed leveling experience, improving the success rate of 3D printing. The probe of 3D touch V3.2 Pro has an accuracy deviation within 0.005mm, offering you a higher precision and stability than older metal probes.  The 3D Touch v3.2 Pro adopts a high sensitivity Hall sensor, compared with capacitive sensor or inductive sensor, it is not affected by the hot bed material, allowing you to use it on glass,metal, plastic and other common material hot beds without interference concerns.  Geeetech test each 3DTouch v3.2 Pro for accuracy before leaving the factory, only the products that meet their accuracy standards are allowed to be sold.  Compatible with most Geeetech FDM style printers that accept BL-Touch style sensors, other brands such as Creality, Artillery, Sunlu, Prusia, Easythreed with BL-Touch support should be able to use this sensor but may need firmware updates and a printed mount. Wiring: 3-pin: Brown (-, GND), Red (+5V), Orange (control signal) 2-pin: Black (-, GND), White (Z min) Features： New structural design, higher precision Suitable for various materials hotbeds New industrial design New surface treatment High precision, accuracy deviation is ±0.005mm Automatic detection after power on Abnormal alarm More stable and reliable Intelligent measurement Included Parts: 3D-touch: 1, M3 screws: 4, M3 nuts: 2, Metal holder: 1, 18cm cable: 1, 100cm cable: 1 Power supply: DC 5V, Current:15mA～300mA

Building on their previous model Geeetech have gone back to the drawing board and released this new and updated auto bed level sensor for 3D Printers. The 3D touch v3.2 Pro is a new generation of FDM 3D printer hot bed automatic leveling accessory. It is compatible with glass, wood, metal and other materials of hot bed, bringing you a simpler and faster hot bed leveling experience, improving the success rate of 3D printing. The probe of 3D touch V3.2 Pro has an accuracy deviation within 0.005mm, offering you a higher precision and stability than older metal probes.  The 3D Touch v3.2 Pro adopts a high sensitivity Hall sensor, compared with capacitive sensor or inductive sensor, it is not affected by the hot bed material, allowing you to use it on glass,metal, plastic and other common material hot beds without interference concerns.  Geeetech test each 3DTouch v3.2 Pro for accuracy before leaving the factory, only the products that meet their accuracy standards are allowed to be sold.  Compatible with most Geeetech FDM style printers that accept BL-Touch style sensors, other brands such as Creality, Artillery, Sunlu, Prusia, Easythreed with BL-Touch support should be able to use this sensor but may need firmware updates and a printed mount. Wiring: 3-pin: Brown (-, GND), Red (+5V), Orange (control signal) 2-pin: Black (-, GND), White (Z min) Features： New structural design, higher precision Suitable for various materials hotbeds New industrial design New surface treatment High precision, accuracy deviation is ±0.005mm Automatic detection after power on Abnormal alarm More stable and reliable Intelligent measurement Included Parts: 3D-touch: 1, M3 screws: 4, M3 nuts: 2, Metal holder: 1, 18cm cable: 1, 100cm cable: 1 Power supply: DC 5V, Current:15mA～300mA

The Two Trees Auto Touch Module, provides a BL-Touch compatible upgrade to many 3D printers to assist with bed levelling issues. A flat bed is one of the most critical things for a successful 3D print, an uneven bed can cause issues with the first layers not sitting on the bed correctly. There is also the issue of the bed becoming slightly out of line after a long or large print. Once installed and set up your 3D printers can allow and adjust for the slight variances to ensure optimum printing conditions and reduce failure rates from a slightly off bed level.Installation varies between printers, however the general principle is similar enough. Firstly mount the 3D Touch unit to your printer (you may need to print a mount). Secondly hook up the connections (a lot of printers have a 'BL-Touch' connector on the extruder assembly, some older ones may require wiring to the mainboard. Finally activate the 'Auto Level' feature in a menu or through updating the firmware. Features: The Auto Levelling sensor is a device that uses the hall effect to achieve levelling. The Position of the point can be obtained by touching the point on the heated bed and then compensated by adjusting the Z axis height during printing Printing can also be achieved even though the heated bed is not flat Specifications: Voltage: 5V Current: 15mA Max Current(Peak): 300mA Shell Material: PC Cable Length: short 200mm long 1000mm Package Included:1* Leveling Sensor1* 200mm Cable1* 1000mm Cable2* M3 nuts and screws2* XH2.54mm Terminals1* Coiling Terminal Wiring: 3 Pin:Green: GND Red: +5V Orange: Signal Cable 2 Pin:Black: GND White: Z-min Example Configuration ⠀ Return to top

The Geeetech 3D Touch V3.2 Module, provides a BL-Touch compatible upgrade to many 3D printers to assist with bed levelling issues. A flat bed is one of the most critical things for a successful 3D print, an uneven bed can cause issues with the first layers not sitting on the bed correctly. There is also the issue of the bed becoming slightly out of line after a long or large print. Once installed and set up your 3D printers can allow and adjust for the slight variances to ensure optimum printing conditions and reduce failure rates from a slightly off bed level.Installation varies between printers, however the general principle is similar enough. Firstly mount the 3D Touch unit to your printer (you may need to print a mount). Secondly hook up the connections (a lot of printers have a 'BL-Touch' connector on the extruder assembly, some older ones may require wiring to the mainboard. Finally activate the 'Auto Level' feature in a menu or through updating the firmware. Features: Updated Plastic Probe version, more precise than the older Metal Tip Easily upgrade your 3D printer to Auto Levelling High precision touch sensor Compatible with many brands of 3D printer such as Creality, Anet, SUNLU, Artillery, Geeetech and more. Self-test: The push pin is operated three times to test when the power is on Alarm: The LED light blinks if a problem found on a self-test or on an operation 3D Touch's Standard Deviation in repeatability is around 0.02mm. If you choose 3D Touch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience. 3D Touch does not uses either optical, nor proximity (inductive/capacitive) sensor. 3D Touch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely. This is an auto leveling sensor for 3D Printers based on open-source. Simple, Smart, High-precision, It could work with any kinds of bed materials, such as glasses, woods, metals, and so on. It can be operated in the following conditions: One I/O for control (PWM or Software PWM) One I/O for Zmin(Z Probe) GND and +5V power Specifications ⠀ Model: 3D-Touch (BL-Touch compatible) CPU: Atmel ATtiny13A Voltage: 5V Current: 15mA Max. Current: 300mA Cable length: 150mm Weight: 10g Wiring: 3-pin: Brown (-, GND) Red (+5V) Orange (control signal) and 2-pin: Black (-, GND) White (Z min) Dimensions: Installation Notes ⠀ Additional power supply can be needed in case which your board does not supply enough amperage. Electronic devices can be damaged or even destroyed if connected to the wrong side polarity. [wrong terminal connect to 5V(+) and GND(-)] Install 3D-Touch/BL-Touch as far as possible from magnetic, motor, fan etc. Please handle the measuring pin with care, hard pushes or pulls can make the 3D Touch/BL-Touch less accurate. Fix push-pin with locking paint after reassembling or adjusting core. Please do not change the position of the hex screw(core). Do not separate or deform elastic material attached on the push-pin. Package includes: 1 X Sensor 1 X 3 Pin Straight Pin 1 X 2 Pin Straight Pin 2 X Screw, Nut and Washer 2 X Dupont Housing Shell 3Pin 2 X Dupont Housing Shell 2Pin 10X Dupont Terminal 1 X 10KΩ 1/8W Resistor for Smoothieboard Links to Additional Resources ⠀ Geeetech 3DTouch Product Page Geeetech 3D Touch Wiki Geeetech 3D Touch Manual (pdf) Geeetech 3DTouch YouTube Playlist Geeetech Facebook Group Thingiverse Bl-Touch Mount Prints YouTube Bl-Touch Mount Videos