Sold out
MicroSD to SD Card Adapter Converter Kit 48cm Long For 3D Printer with 8GB SD Card - NSE Imports MicroSD to SD Card Adapter Converter Kit 48cm Long For 3D Printer with 8GB SD Card - NSE Imports
Unbranded
Ships from: CN Warehouse
MicroSD to SD Card Adapter Converter Kit 48cm Long For 3D Printer with 8GB SD Card £15.99

Description: Save wear and tear on your expensive 3D printer's SD card slot with the handy Transflash (TF) / Micro SD to SD card adapter. Simply plug the dummy micro SD connector into your printer and then use the included full size SD card in the slot at the end of the extension. Comes complete with everything pictured. While marketed for 3D printers these are also ideal for many jobs where you may need to have easy access to a card. Mobile phone repairs, Game Console Mods, Flash carts, Cameras, SCSI-to-SD, IDE-to-SD, GDEMU, SD2SP2 or similar devices are among others uses it could be put to. Basically if it has a TF/Micro SD slot and you are always swapping cards around maybe this will help you. Features: All the cool details Save wear and tear on your devices Micro SD / Transflash (TF) slot Make your SD Card more accessible, great for frequent card changes Ideal for many use cases Specifications: The technical stuff Cable length: 48cm (approx) Package includes*: 1 x TF/Micro SD to SD Converter with 48cm ribbon, 1x 8GB SD Card, 1x TF/Micro SD Card Reader, 1x 8GB TF/Micro SD Card. *Please note: Exact contents may vary in appearance but are all functionally identical Additional Images and Videos: More images of this item.

Creality 3D® Upgraded Version V1.1.5 24V Super Silent Mainboard Motherboard With TMC2208 Driver For Ender-3 / Ender-3 Pro 3D Printer - NSE Imports Creality 3D® Upgraded Version V1.1.5 24V Super Silent Mainboard Motherboard With TMC2208 Driver For Ender-3 / Ender-3 Pro 3D Printer - NSE Imports
Creality 3D
Ships from: UK Warehouse
Creality 3D® Upgraded Version V1.1.5 24V Super Silent Mainboard Motherboard With TMC2208 Driver For Ender-3 / Ender-3 Pro 3D Printer from £20.99

Features: 1. With speicial power chip, support 24V power input 2. The circuit board is optimized by circuit, effectively solve the heating problem 3. Can work with E/Z/Y/X a-xis motor 4. With USB interface, easy to operate 5. Newest version with super silent TMC2208 driver Note: Ender-3 / Ender-3 Pro use the same mainboard but different firmware, please select the type you need Package Included: 1x Mainboard  

Sold out
5Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable - NSE Imports 5Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable - NSE Imports
Geekcreit
Ships from: UK Warehouse
5Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable £5.99

Features: It using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees. Is the common connection of thin copper wire can not match. Not easy to pull off, plug it convenient, for ease of use, plug the other side to do the one, you can use the direct plug Board Size: Approx. 39 x 16 x 7mm / 1.54 x 0.63 x 0.28 inch Cable Length: Approx. 70 cm / 27.56 inch Connection Description: Red line connecting VCC (ramps of +) Connect the black wire GND (ramps of -) Green Line connection SIGNAL (ramps in s) Tips: Under normal circumstances, the system must be configured to at least three mechanical switches. Package Includes: 5 x 3D Printer Endstop Switch

2pcs MOSFET High Power Heated Bed Expansion Power Module MOS Tube  for 3D Printer Prusa i3 Anet A8/A6 - NSE Imports 2pcs MOSFET High Power Heated Bed Expansion Power Module MOS Tube  for 3D Printer Prusa i3 Anet A8/A6 - NSE Imports
Unbranded
Ships from: CN Warehouse
2pcs MOSFET High Power Heated Bed Expansion Power Module MOS Tube for 3D Printer Prusa i3 Anet A8/A6 £9.99

Specifications:   1. Colour: Black 2. Maximum current: 25A (enhanced heat dissipation) 3. Size: about 6 x 5 x 3.1cm  4. Mounting holes: 3.2mm diameter, for M3 screws Features:   - This module is positioned between the output of the heating bed or extruder and your electronic board as shown in the wiring diagram.  - The white connector cable is provided. - With this additional module, the maximum current on the board can reach 25A. - This module is recommended if you plan to use a heated bed with a 3D printer that uses a 12V power supply.   Content:   Simple - 1 MOSFET                 - 1 Cable   Double - 2 MOSFET                 - 2 Cables                 - 2 Nozzles 0.4mm for wire of 1.75mm Package Included: 2 x Heated bed power module with cable            

Sold out
10Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable - NSE Imports 10Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable - NSE Imports
Geekcreit
Ships from: CN Warehouse
10Pcs Geekcreit® RAMPS 1.4 Endstop Switch For RepRap Mendel 3D Printer With 70cm Cable £9.99

Features: It using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees. Is the common connection of thin copper wire can not match. Not easy to pull off, plug it convenient, for ease of use, plug the other side to do the one, you can use the direct plug Board Size: Approx. 39 x 16 x 7mm / 1.54 x 0.63 x 0.28 inch Cable Length: Approx. 70 cm / 27.56 inch Connection Description: Red line connecting VCC (ramps of +) Connect the black wire GND (ramps of -) Green Line connection SIGNAL (ramps in s) Tips: Under normal circumstances, the system must be configured to at least three mechanical switches. Package Included: 10 x 3D Printer Endstop Switch           ,,

6

Free Tracked Shipping to most countries*

*Some country/warehouse combinations may have fees due to high shipping costs.

Secure Payments

We accept most Cards, PayPal, Amazon Pay, Google Pay and Apple Pay